CNC Equipment Huge Assortment
Posted: Sun Feb 16, 2014 4:58 pm
SOLD SOLD SOLD 
I have a 2'x3' CNC router that I built from a kit from Fine Automation.
With the appropriate spindle it can do aluminum. I have about $3000 in it but I have never used it and never will
because of various reasons but it is just to large and heavy to ship. It has an aluminum bed.
It would take a few heavy boxes that I am unable to pick up. I am disabled because of a bad back that is inoperable. Don't want
to get into that here but trust me, I cannot pick up such a box.
I do want to sell everything but it has to be to someone local enough to pick the stuff up.
First is a 2' x 3' CNC router. Link to be barebones kit without electronics- http://www.finelineautomation.com/produ ... router-kit
I also have a Gecko Drive G540 Driver, 3 KL-9082PbF Drivers, 2 of the Antek Toroidal Power supplies, 50V and 63V.
Heavy duty tracks which consists of Hiwin AGR25 - (2) 4' with 2 blocks each (2) 3' with 2 blocks each (2) 14" with 2 blocks each.
Also included is a Harbor Freight Mill that still has the red grease on it because it has never been used along with the CNC kit for it and many cutters.
I am getting rid of all this stuff because of my back. I cannot use the stuff so I've decided to get rid of everything for a price that is really attractive.
Probably would throw in a Harbor Freight 8" Lathe that has never been used. Almost forgot the new Bosch Colt router that I was going to use on the
CNC machine. I think there is 6 or 8 Kelinginc Nema 23 motors. Anyone interested has to travel to near Youngstown, Ohio and disassemble the stuff
enough to get it out of the basement and bring a helper because stuff like the mill is heavy and I cannot help. PM if interested and leave email or phone number. Cost for all the above $500
In April or May I am going to list all this for the same price on CNCZONE, there has to be someone living near me who has a need.
I have a 2'x3' CNC router that I built from a kit from Fine Automation.
With the appropriate spindle it can do aluminum. I have about $3000 in it but I have never used it and never will
because of various reasons but it is just to large and heavy to ship. It has an aluminum bed.
It would take a few heavy boxes that I am unable to pick up. I am disabled because of a bad back that is inoperable. Don't want
to get into that here but trust me, I cannot pick up such a box.
I do want to sell everything but it has to be to someone local enough to pick the stuff up.
First is a 2' x 3' CNC router. Link to be barebones kit without electronics- http://www.finelineautomation.com/produ ... router-kit
I also have a Gecko Drive G540 Driver, 3 KL-9082PbF Drivers, 2 of the Antek Toroidal Power supplies, 50V and 63V.
Heavy duty tracks which consists of Hiwin AGR25 - (2) 4' with 2 blocks each (2) 3' with 2 blocks each (2) 14" with 2 blocks each.
Also included is a Harbor Freight Mill that still has the red grease on it because it has never been used along with the CNC kit for it and many cutters.
I am getting rid of all this stuff because of my back. I cannot use the stuff so I've decided to get rid of everything for a price that is really attractive.
Probably would throw in a Harbor Freight 8" Lathe that has never been used. Almost forgot the new Bosch Colt router that I was going to use on the
CNC machine. I think there is 6 or 8 Kelinginc Nema 23 motors. Anyone interested has to travel to near Youngstown, Ohio and disassemble the stuff
enough to get it out of the basement and bring a helper because stuff like the mill is heavy and I cannot help. PM if interested and leave email or phone number. Cost for all the above $500
In April or May I am going to list all this for the same price on CNCZONE, there has to be someone living near me who has a need.
