Welcome to the SeeMeCNC Community

I notice its only showing the last 8 months of gps tracking for me. Since I've used Google phones back to at least 2009, i wonder if it only keeps it for 8 months. Also, I noticed that some of the GPS locations show me out of state when I havent been at all (who wants to go to Nevada??). So it's not ...

Thanks. Now all I have to do is figure out why my XY and Z axis are off after installing the new .91 firmware.

This is on myinitial start up after installing the firmware.

https://www.flickr.com/photos/46214978@ ... otostream/

http://www.flickr.com/groups/3d-print-failures/

http://gizmodo.com/11-spectacular-3d-pr ... -511092085

http://www.pinterest.com/deegeejay/3d-p ... ul-errors/

bad news, its the PSU.....good news, i have another fan for the printer?

I just started a print, laid down one perimeter, then shut off. I flipped the switch off then back on, I get a quik lcd light up then goes back off. The little led light on the Rambo also flicks on then off. I honestly have less than 60hrs of print time on this thing. Ive replaced the Rambo, pulley ...

Tried different levels of temp's but its still not stcking to the bed. I can pull it off with ease. Ive also tried diff layer hieghts and running at 40mm/s spd. I know once it gets to a certain height, the nozzle will move the print right off the bed

You have a bad reel. I had the same problems and I was getting almost 2mm diameter in some areas. SeeMe was nice enough to replace the one I bought from them because of the problems I had. Now the one I have works just fine through the tubes however its still inconsistent and diameters by Almost ...

Thnx. Ill have to look at netfabb and see if it works on my end.

It's been a few months, I'll have to relook at that. When I was talking .23-.5mm, I was referring to the arc between towers that the nozzle made. As it left the Y tower it gradually arced to its high point of .5 then back down to bed level as it got to the X tower. As far and resquaring, Again ill ...

Can't wait for this to be sold. I'll buy a few. The beginning is goofy, but the concept looks great.

[youtube]http://www.youtube.com/watch?v=jXFp2pQvG9A[/youtube]

It works for the center of the bed, not the outer radius. Calibration per the manual is all set, but the outer diameter between the towers are the issues.

http://www.thingiverse.com/thing:122957

I did rainbow dash for my daughter.
Thnx

This is what I get when I sliced a pony

[img]http://i1326.photobucket.com/albums/u65 ... 457bfa.jpg[/img]

If you notice, it doesn't look all there. When I sliced with kisslicer I got a full picture.

I noticed my nozzle lifts up about .23mm-.50mm at 50-90mm from the center of my bed and inbetween the towers. Doing the calibration,the axis' and center are great, but traveling the outer diameter my nozzle convexes between towers. Im using the glass bed and have the nozzle and bed heated while ...

Im having issues with my printer delaying filament extruding about 20mm. It would run half of a perimeter before it starts to extrude filament. I'm using slic3r. When I have used Kisslicer, it lays filament right away (having issues with kisslicer laying too much and starts to curl and stick to the ...

Thanks. Although I have tried KISSlicer, but my prints have come out worse than slic3rs when I load the gcode. I might have to tweak the setting some more.

I printed this pumkin. and while it has some layering flaws, it came out ok. Im thinking its partly the filament. but it couldn't print the upp teeth all the way. Any .10 cents? [img]http://i1326.photobucket.com/albums/u652/m4r1n5/3d%20Printer/DSC00003_zpse92b8636.jpg[/img] [img]http://i1326 ...

Found this while googling info. http://www.kronosrobotics.com/3d/rostock/index.shtml I thought it was really well written. Gave his issues, found different solutions. While he didn't give it the thumbs up, I thought his extruder and stop switch ideas were pretty good. His extruder/hot end were ...

dpmacri wrote: Another thing I've started doing is to manual extrude filament with different temperatures to see where it comes out easy enough that it's not curling up a bunch at the end of the nozzle, but not so fast that it starts oozing a ton. Could you elaborate on this? Mine HAS been sort of ...

PLA, 190 & I only had the bed temp at 35c. My ASSUMPTION was the bed is to prevent curling, so I was playing with the bed temp, but didnt think it would have any affect on the higher layers. Also, I dont have a fan cuz I cant print one, lol. If Seemecnc sold one, I would buy it.

I FINALLY have my printer running consistant!....sort of... After finding one of the stepper teeth was EVERYTHING and fixing it, now it tweaking things. The print on the left was my first print and it came out ok, but the print on the right was the next print and I got the squigglys. Not sure if it ...

Got it. Replaced it. Fixed the end stop issue, lean issue, world hunger, and lowered gas prices. I post pics when photobucket stops acting up.

Im sure they would. Theyve replaced the Arduino (bad z-axis issues) board and the adapter board( my bad on the soldering). I'm going to buy the pulleys because I want extras just in case. Theyve done a great job working with me and my limited knowledge of 3d printers. Hopefully I'll get back to ...

I bought mine in June. I thought they went away from the all aluminum ones since they're selling mine on the website right now.